# Peripheral Installation Guide

## 1. **Installing the Joystick Module**

{% hint style="warning" %}
**Note:** When connecting the data box to the joystick module, ensure that the data cable is positioned such that the UDCAP logo is either both facing up or both facing down.
{% endhint %}

**Insert the joystick module connection cable into the Type-C port on the inner side of the glove.**

<div align="left"><figure><img src="/files/CWVTQUMwBRR1tIOusN9K" alt="" width="375"><figcaption></figcaption></figure></div>

&#x20;**Attach the joystick module to the index finger using the Velcro on the module.** Adjust it to ensure a comfortable and snug fit.

### Left Hand：UDCAP logo facing up.

<div align="center"><figure><img src="/files/eJpi0KYU1ME1xJJbHXBn" alt="" width="375"><figcaption></figcaption></figure> <figure><img src="/files/9LZngr5a9163UNsvyTGo" alt="" width="375"><figcaption></figcaption></figure></div>

### Right Hand：UDCAP logo facing Down.

<div><figure><img src="/files/2zktVQ2nndtDlAR2TYX4" alt="" width="375"><figcaption></figcaption></figure> <figure><img src="/files/PkvBJTdDaL2MYPjSUZIZ" alt="" width="375"><figcaption></figcaption></figure></div>

***

## **2. Select your controller for installation**

{% hint style="warning" %}
**Note:** The top and bottom snap fasteners are of different lengths, so be careful when installing them!
{% endhint %}

{% tabs %}
{% tab title="VIVE Tracker 3.0" %}

<div align="left"><figure><img src="/files/YJGUvVKFdCeJ1cq4vw7S" alt="" width="375"><figcaption></figcaption></figure></div>

Place the mounting adaptor at the bottom of the Tracker, ensuring that the mounting points on the adaptor and the bottom of the Tracker align. Insert the 1/4 standard screw into the screw hole and turn it clockwise.

<div align="left"><figure><img src="/files/WZPYNG7UYgJbWcGlcPZL" alt="" width="375"><figcaption></figcaption></figure></div>

**Fix the Tracker and the mounting adaptor onto the glove data box.** Note that the grooves on the top and bottom of the mounting adaptor have different widths to prevent confusion about the fixing direction.

<div align="left"><figure><img src="/files/VgrTd6bqSM8vpFl6zbMi" alt="" width="375"><figcaption></figcaption></figure></div>
{% endtab %}

{% tab title="Tundra Tracker" %}

<div align="left"><figure><img src="/files/69puRfXqnYkBlUvqnbR9" alt="" width="375"><figcaption></figcaption></figure></div>

Remove the two screws at the bottom of the Tundra and detach the Tundra adaptor.

Replace the original Tundra base with the UDCAP Tundra mounting adaptor.&#x20;

Note that on the inside of the UDCAP Tundra mounting adaptor, there is an oval mark. This mark should align with the direction of the Tundra's Type-C charging port (QR code).

After tightening the screws, fix the Tundra mounting adaptor onto the data box on the glove.&#x20;

<div align="left"><figure><img src="/files/DlTCrF5ekGYngOVOzHjx" alt="" width="375"><figcaption></figcaption></figure></div>
{% endtab %}

{% tab title="VIVE Ultimate Tracker" %}

<div align="left"><figure><img src="/files/bYUg4l0nYLyGrbjIcV58" alt="" width="375"><figcaption></figcaption></figure></div>

The UTK mounting adaptor installation method is the same as the official UTK base installation method. Secure it to the mounting adaptor using the clips. Ensure that the raised oval mark on the mounting adaptor aligns with the extension port at the bottom of the UTK.

<div align="left"><figure><img src="/files/Il3okKEbC62drIXOQuuQ" alt="" width="375"><figcaption></figcaption></figure></div>

<div align="left"><figure><img src="/files/q8V18n3s3dUazq90HopF" alt="" width="375"><figcaption></figcaption></figure></div>
{% endtab %}

{% tab title="Quest" %}

<div align="left"><figure><img src="/files/Qftc2c8Cop7HC7HRXzj2" alt="" width="375"><figcaption></figcaption></figure></div>

Rotate the Quest adaptor screws to open the fixed base and place the Quest controller (trigger down) into the base, noting that the trigger needs to fit into the recessed portion of the base.

<div align="left"><figure><img src="/files/QFMnCGBPfL0oa93EdKNt" alt="" width="375"><figcaption></figcaption></figure></div>

Tighten the screws.

<div align="left"><figure><img src="/files/FP5N1h78NW19oyMQ4oiS" alt="" width="375"><figcaption></figcaption></figure></div>

Attach the quest handle strap behind the wrist and to the back of the glove via the base snap.

&#x20;Pay attention to the direction of the handle.

<div><figure><img src="/files/eifihsuSZH31eMEaT0xR" alt=""><figcaption></figcaption></figure> <figure><img src="/files/IltNxcFTgm1AEjfJG7ib" alt=""><figcaption></figcaption></figure></div>

<div><figure><img src="/files/3r1MKEBZedZXnSLeLoNj" alt=""><figcaption></figcaption></figure> <figure><img src="/files/9OJPnj2ZrJqQ6OHcwr8T" alt=""><figcaption></figcaption></figure></div>
{% endtab %}
{% endtabs %}


---

# Agent Instructions: Querying This Documentation

If you need additional information that is not directly available in this page, you can query the documentation dynamically by asking a question.

Perform an HTTP GET request on the current page URL with the `ask` query parameter:

```
GET https://udcap-vr-gloves-document.gitbook.io/udcap/hardware-setup/peripheral-installation-guide.md?ask=<question>
```

The question should be specific, self-contained, and written in natural language.
The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.